Construction Machinery CDM6150 features:
The CDM6150 - Our mid range Excavator
Where Efficiency rules, made tough and for high performance yet achieves the best power savings at a minimum cost.
The original Cummins Engine guarantees high reliability and durability.
Ensures the quality of engine air intake.
Efficient cooling system.
Swings and rotates with precision and control.
Auxiliary Hydraulic Valve
The main valve is provided with a set of standby valves to facilitate the installation of other accessories such as the breaking hammer.
Equipped with a high quality hydraulic oil filter which can prolong the life of the machine.
Power Control Mode
There are 3 different power modes
(H mode) heavy-duty power mode
(S mode) saving power mode
(L mode) Light-duty power mode
The machine can switch at will to reduce the power loss. The combination of 3 modes can reduce the fuel consumption and better meet the different working conditions.
Fault Auto Warning
Built in Fault and Warning Alert system.
Engine Overheating Auto Protection
The overheating protection will be active if the coolant temperature exceeds 102℃. Then the engine will not flameout while the system will reduce the engine speed. However, if the coolant temperature is too high, the operator should shut down the machine as required and find out the faults cause.
Low Oil Pressure Protection
When oil pressure is below the standard value, the oil pressure switch will be closed, the text warning will display for 3s and then the engine will slow down to low idle speed.
Maintenance Auto Reminder
The monitor will periodically remind the operator of changing the engine oil, grease and filter element at the set interval to support a routine service.
Standard Cab Equipment
The cab inside includes the cigar lighter, ash tray, cup holder, coat hook, cubbyhole and storage rack.
High performance A/C system.
Safety Lock Joystick
The hydraulic safety lock joystick is located at the outside of the left armrest box in the cab.
Boom and Arm
Made of high strength low alloy structural steels.
Made with a thick chrome plating coat and high surface finish. This special treatment enables the extremely high wear resistance and corrosion resistance.
The bucket body is made of low alloy and the external structure is made of high strength and wear-resistant steels, which constitute the entire reinforced bucket. This excavator provides different bucket options to meet different working demands.
|Rated power||86 kW (117hp) /2200 rpm||90 kW (122hp) /2200 rpm|
|Max. torque||424 N.m/1600 rpm||489 N.m/1500 rpm|
|Bore× Stroke||102mm×120mm||107 mm×124 mm|
|Displacement||3.9 L||4.5 L|
|Comment||Maintain the rated power at 2300m elevation.|
|Operating weight||Summary||Operating weight：14000kg |
|Ground pressure||45 kPa|
|Fluid capacity||Fuel tank||270 L|
|Cooling system||23 L|
|Engine oil||14 L|
|Swing drive unit||1.8 L|
|Traveling gear||2×2.5 L|
|Hydraulic oil tank||159 L|
|Swing mechanism||Summary||High torque plunger motor and 2-stage planetary reducer drive.|
|Swing speed||11.9 rpm|
|Travel drive||Summary||The integrated 2-speed plunger hydraulic motor and reducer drive, motor piparranged.|
|Taveling speed||3.34 -5.5 km/h|
|Traveling mechanism||Standard track shoe width||600 mm|
|No. of track shoe||43 (each side)|
|No. of carrierrollers||2 (each side)|
|No. of track rollers||7 (each side)|
|Hydraulic system||Main pump||Duplex axial variable plunger pump|
|Pilot pump||gear pump (integrated in main pump)|
|Max. flow of system||2×120 L/min|
|Max. pressure of equipment||34.3 MPa|
|Max. pilot pressure||3.9 MPa|
|Operating equipment||Each machine action is under the pilot control.|
|Electrical system||System voltage:24 V Battery:12 V，120 A×2|
The following sizes approximate to that of the equipment of standard configuration.
|Boom Length (mm)||4600|
|Arm Length (mm)||2500|
|a Transport length(mm)||7930|
|b Total transport height(mm)||3070|
|c Tumblers distance (mm)||2880|
|d Tail slewing radius(mm)||2250|
|e Counterweight ground clearance(mm)||924|
|f Track gauge(mm)||1990|
|g Total transport width(mm)||2590|
|h Upper structure width(mm)||2500|
|i Standard track shoe width(mm)||600|
|J Min. ground clearance(mm)||422|
The following sizes approximate tothat of the equipment of standard configuration.
|Boom Length (mm)||4600|
|Arm Length (mm)||2500|
|aMax. digging radius(mm):||8336|
|b Max. digging depth(mm):||5542|
|c Max. digging height(mm):||8343|
|d Max. dumping height(mm):||6160|
|e Max. digging radius on ground(mm):||8214|
|Max. bucket breakout force-ISO(kN):||132.4|
|Max. arm breakout force-ISO(kN):||85.6|
|Standard Equipment |
The following equipment items are part of the whole standard equipment.
|70 A alternator||Aerial and harness (excluding radio speaker)|
|Platform working lamp (1)||Suspension type adjustable seat|
|Boom working lamp (1)||Retractable seat belt (2" width)|
|Cab lamp (1)||Ash tray and cigar lighter|
|Refuelling pump||Cup holder|
|Original Cummins engine||A/C system allowing fast defrosting|
|Radial seal air filter||Hydraulic safety lock joystick|
|Oil-water separator||File pocket|
|Fuel filter||Hat-and-coat hook|
|Rippled wall radiator with cleaning space||Left/right side storage|
|High-volume fuel tank||Interior lighting equipment|
|Auxiliary hydraulic valve (1)||Double stereo speaker|
|Auto swing parking brake||Openable skylight|
|Boom/Armholding control function||Wiper and washer|
|Counterweight||Cab positive pressure filtration and ventilation system|
|Top bonnet||Rear window (escape exit)|
|Gate lock and cover lock||Escape hammer|
|A/C stationary condenser||Washable rubber floor mat|
|Arm re-activation circuit||Fire extinguisher|
|Boom/Armconfluence||Color graphic display|
|Straight travelling hydraulic circuit||Economic mode selection|
|Double speed travel||Date and time display|
|Front idler and idler cushion||Machine state display|
|Trailer ring on base frame||Working hour display, maintenance remind|
|Chain guard rack||Current engine speed display|
|Adjustable seat armrest||Warning message|
|Optional Equipment |
The optional equipment may be different from this manual. For more information, contact the local LONKING agent.
|Bucket||Operating console||Undercarriage||Auxiliary hydraulic unit and pipeline|
|General bucket 0.25m³ General bucket 0.40m³ General bucket 0.56m³ Loose materialbucket 0.67m³ Loose materialbucket 0.75m³||Working warning lamp||500mm triple grouser shoes||Breaking hammer pipeline|
|Cab roof protecting net||700mm triple grouser shoes||Hydraulic breaking hammer|
|Cab front protecting net||Track rubber block|
|Travel warning device|